无法让 lm 传感器加载 ATI Radeon 温度和风扇或输出所有设置

Question

Linux 新手并且有小问题：/。我最初遵循了本指南，但没有收到正确的输出，也没有显示我的 ATI Radeon HD 5000 温度或风扇速度。然后使用本指南，表现出同样的问题。安装没有问题，也没有错误。我认为由于某种原因它没有阅读 i2c。专有驱动程序已根据 fglrxinfo 安装并正常运行。我可以使用 aticonfig 命令并查看温度和风扇。在搜索了两个星期的互联网后，我仍然没有找到任何解决方案或如何使其正常工作。

关于如何让 ATI Radeon 传感器在“传感器”下工作的任何想法？

当我运行“sudo sensor-detect”时，这是我的输出

# sensors-detect revision 5984 (2011-07-10 21:22:53 +0200)
# System: LENOVO IdeaPad Y560 (laptop)
# Board: Lenovo KL3

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): y
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
AMD Family 12h and 14h thermal sensors...                   No
AMD Family 15h thermal sensors...                           No
AMD Family 15h power sensors...                             No
Intel digital thermal sensor...                             Success!
    (driver `coretemp')
Intel AMB FB-DIMM thermal sensor...                         No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor/ITE'...               Yes
Found unknown chip with ID 0x8502
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): y
Using driver `i2c-i801' for device 0000:00:1f.3: Intel 3400/5 Series (PCH)

Now follows a summary of the probes I have just done.
Just press ENTER to continue: 

Driver `coretemp':
  * Chip `Intel digital thermal sensor' (confidence: 9)

To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
coretemp
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!

Do you want to add these lines automatically to /etc/modules? (yes/NO)

我的“传感器”输出是：

acpitz-virtual-0
Adapter: Virtual device
temp1:        +58.0°C  (crit = +100.0°C)

coretemp-isa-0000
Adapter: ISA adapter
Core 0:       +56.0°C  (high = +84.0°C, crit = +100.0°C)
Core 1:       +57.0°C  (high = +84.0°C, crit = +100.0°C)
Core 2:       +58.0°C  (high = +84.0°C, crit = +100.0°C)
Core 3:       +57.0°C  (high = +84.0°C, crit = +100.0°C)

我的“/etc/modules”是：

# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.

lp
rtc

# Generated by sensors-detect on Fri Nov 30 23:24:31 2012
# Chip drivers
coretemp

更新：我仍然遇到这个问题。我已经完成了全新的操作系统安装，并尝试了通过非官方 wiki 安装 fglrx 的所有可能方法。任何帮助的想法都非常感谢。

Answer 1

为什么不使用aticonfig工具来获取当前GPU温度？

aticonfig --adapter=all --odgt

Answer 2

据我所知，ISA 适配器温度就是您的 ATI Radeon 温度。我这样说是因为有时，如果驱动程序没有提供扩展名（ISA、PCI、PCIe 等），系统可能会自动通过 ISA 总线号来调用它。