连接到 USB 插座的 2.5" 笔记本外置硬盘的典型功耗是多少?

tri*_*iwo 14 laptop power-supply ssd hard-drive power-consumption

连接到笔记本电脑 USB 端口作为外置硬盘驱动器的 2.5" 笔记本电脑外置硬盘 7200RPM SATA (300Gb) 的近似功率和电流消耗是多少?

我听说使用普通硬盘连接到笔记本电脑的 USB 插座作为外部驱动器对主板来说不是很好,因为与 SSD 驱动器或 USB 闪存驱动器相比,由于主板上的额外负载,因为硬盘驱动器需要更多的电力来驱动.

以下是有关功耗的一些信息:

平均功耗

stu*_*pix 9

问这个问题已经快三年了,但我认为我的回答对某些人来说仍然是真实的。

我也对现代 2.5" 驱动器的功耗感到好奇,但除了这个讨论和关于 500 Gb 驱动器的 THG 文章(在问题中提到)之外,没有找到任何好的文章。经过进一步的谷歌搜索,我找到了希捷的官方规范Barracuda 2.5" 3/4/5 Tb 驱动器,用于启动/读取/写入/睡眠模式。

由于所有现代 2.5" HDD 在它们的实现中或多或少都很常见,我们可以使用此规范作为参考,但请记住,与此驱动器相比,其他驱动器的偏差可能高达 20%(如问题表中所示)。

出于存档目的,这里是规范的摘录。

Typical power measurements are based on an average of drives tested,
under nominal conditions, at 25°C ambient temperature. These power
measurements are done with DIPM enabled.

• Spinup current is measured from the time of power-on to the time
  that the drive spindle reaches operating speed.

• Read/Write current is measured with the heads on track, based on
  three 64 sector read or write operations every 100 ms.

• The drive supports two idle modes: Active Idle mode and Low Power Idle mode.

??????????????????????????????????????????????????????
? Power Dissipation      ? 5TB, 4TB & 3TB models     ?
?                        ? +5V input average (25° C) ?
??????????????????????????????????????????????????????
? Spinup (max)           ?     1.2A (6W)             ?
??????????????????????????????????????????????????????
? Write average          ?     2.10W                 ?
??????????????????????????????????????????????????????
? Read average           ?     1.90W                 ?
??????????????????????????????????????????????????????
? Idle, low power mode   ?     0.85W                 ?
??????????????????????????????????????????????????????
? Standby/sleep          ?     0.18W                 ?
??????????????????????????????????????????????????????
 Standby power is measured at steady state (after 200ms from transition)
Run Code Online (Sandbox Code Playgroud)

PS: 我与希捷公司没有任何可能的关联。


Mic*_*ras 6

您的解决方案是测量功率。我可以看到两种方法来实现这一目标。

  1. 制作一条 USB 分支电缆,您可以将其与数字万用表一起使用,以测量从 USB 端口提供给外部驱动器的电压和电流。
  2. 购买一款便宜的 USB 测试仪,可为您显示电压和电流。在亚马逊上可以看到这些仪表的一个例子。

在此处输入图片说明

一旦您获得以伏特为单位的电压和以安培为单位的电流,只需将这两个数字相乘即可获得以瓦特为单位的功率。


Gre*_*ine 6

长话短说

\n
    \n
  • Seagate Backup Plus Portable 5 TB 峰值/空闲功耗:4.2/1.4 W
  • \n
  • Seagate Backup Plus Slim 2 TB 峰值/空闲功耗:3.9/1.1 W
  • \n
\n

来自希捷 Backup Plus Portable 5TB 和 Backup Plus Slim 2TB 评测:面向消费市场的 SMR第 4 页

\n
\n

我购买了一些 NanoTech 双端口 USB 3.0 ExpressCard,其报价的额定电流为每个端口 900\xc2\xa0mA。由于我打算将它们与一些 5 TB Seagate“便携式”护照磁盘一起使用,因此我认为我应该检查是否需要 Y 形分路器 USB 电缆来提供所需的电流。

\n

功耗图解:

\n

适用于 5 TB Seagate Backup Plus 便携式硬盘

\n

电流消耗:5 TB Seagate Backup Plus Portable

\n

适用于 2 TB Seagate Backup Plus Slim

\n

电流消耗:2 TB Seagate Backup Plus Slim

\n

请注意,旋转电流可能未显示在图表中,并且可能高于引用的峰值。可能超过 1\xc2\xa0A,如stunpix\'s 答案所示。

\n

希捷 Backup Plus Portable 5TB 和 Backup Plus Slim 2TB 评测中的图表:针对消费市场的 SMR第 4 页)。

\n

从功耗导出峰值/空闲电流值可得出:

\n
    \n
  • 5TB 840/280 毫安
  • \n
  • 2TB 780/0.22 毫安
  • \n
\n

因此,为了旋转起来,为了超级安全,似乎需要 Y 形分路器电缆

\n