SSD 的 SMART 测试已通过，但自检失败
Ian*_*Ian 10 ssd hard-drive smart
我的外部 SSD 本周早些时候遭受了一些文件损坏。型号是
Model Family: Crucial/Micron RealSSD m4/C400/P400
Device Model: M4-CT256M4SSD2
显然，时钟上有 20,000 小时的供电时间。
尽管状态是：
SMART overall-health self-assessment test result: PASSED
自检失败：
gsmartcontrol 将属性报告为：
完整输出为：
smartctl 7.2 2020-12-30 r5155 [x86_64-w64-mingw32-w10-b19045] (sf-7.2-1)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Crucial/Micron RealSSD m4/C400/P400
Device Model: M4-CT256M4SSD2
Serial Number: 0000000012050904896A
LU WWN Device Id: 5 00a075 10904896a
Firmware Version: 0309
User Capacity: 256,060,514,304 bytes [256 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available, deterministic
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Apr 05 11:36:29 2023 PM
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 117) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 1190) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 19) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0
5 Reallocated_Sector_Ct PO--CK 099 099 010 - 36864 (0 5)
9 Power_On_Hours -O--CK 100 100 001 - 19434
12 Power_Cycle_Count -O--CK 100 100 001 - 626
170 Grown_Failing_Block_Ct PO--CK 099 099 010 - 89
171 Program_Fail_Count -O--CK 100 100 001 - 20
172 Erase_Fail_Count -O--CK 100 100 001 - 64
173 Wear_Leveling_Count PO--CK 083 083 010 - 524
174 Unexpect_Power_Loss_Ct -O--CK 100 100 001 - 5
181 Non4k_Aligned_Access -O---K 100 100 001 - 9248 4153 5094
183 SATA_Iface_Downshift -O--CK 100 100 001 - 0
184 End-to-End_Error PO--CK 100 100 050 - 0
187 Reported_Uncorrect -O--CK 100 100 001 - 582
188 Command_Timeout -O--CK 100 100 001 - 0
189 Factory_Bad_Block_Ct -OSR-- 100 100 001 - 85
194 Temperature_Celsius -O---K 100 100 000 - 0
195 Hardware_ECC_Recovered -O-RCK 100 100 001 - 353
196 Reallocated_Event_Count -O--CK 100 100 001 - 89
197 Current_Pending_Sector -O--CK 100 100 001 - 0
198 Offline_Uncorrectable ----CK 100 100 001 - 0
199 UDMA_CRC_Error_Count -O--CK 100 100 001 - 3
202 Perc_Rated_Life_Used ---RC- 083 083 001 - 17
206 Write_Error_Rate -OSR-- 100 100 001 - 20
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 16383 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 255 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 3449 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0 GPL VS 2000 Device vendor specific log
0xa0 SL VS 208 Device vendor specific log
0xa1-0xbf GPL,SL VS 1 Device vendor specific log
0xc0 GPL VS 80 Device vendor specific log
0xc1-0xdf GPL,SL VS 1 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (16383 sectors)
No Errors Logged
SMART Extended Self-test Log size 3449 not supported
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 50% 19433 244627776
# 2 Short offline Completed: read failure 60% 19433 492159152
# 3 Short offline Completed: read failure 60% 16715 492159152
# 4 Vendor (0xff) Completed without error 00% 16602 -
# 5 Vendor (0xff) Completed without error 00% 5107 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 1 (0x0001)
Device State: Active (0)
Current Temperature: 0 Celsius
Power Cycle Min/Max Temperature: --/ 0 Celsius
Lifetime Min/Max Temperature: --/ 0 Celsius
SCT Temperature History Version: 2
Temperature Sampling Period: 10 minutes
Temperature Logging Interval: 10 minutes
Min/Max recommended Temperature: 0/70 Celsius
Min/Max Temperature Limit: -5/75 Celsius
Temperature History Size (Index): 478 (151)
Index Estimated Time Temperature Celsius
152 2023-04-02 04:00 ? -
... ..(473 skipped). .. -
148 2023-04-05 11:00 ? -
149 2023-04-05 11:10 0 -
150 2023-04-05 11:20 0 -
151 2023-04-05 11:30 0 -
SMART WRITE LOG does not return COUNT and LBA_LOW register
SCT (Get) Error Recovery Control command failed
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 2) ==
0x01 0x008 4 626 --- Lifetime Power-On Resets
0x01 0x010 4 19434 --- Power-on Hours
0x01 0x018 6 66167492621 --- Logical Sectors Written
0x01 0x020 6 1499672681 --- Number of Write Commands
0x01 0x028 6 138123876618 --- Logical Sectors Read
0x01 0x030 6 2013843720 --- Number of Read Commands
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 582 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 0 --- Current Temperature
0x05 0x010 1 0 --- Average Short Term Temperature
0x05 0x018 1 0 --- Average Long Term Temperature
0x05 0x020 1 0 --- Highest Temperature
0x05 0x028 1 0 --- Lowest Temperature
0x05 0x030 1 0 --- Highest Average Short Term Temperature
0x05 0x038 1 0 --- Lowest Average Short Term Temperature
0x05 0x040 1 0 --- Highest Average Long Term Temperature
0x05 0x048 1 0 --- Lowest Average Long Term Temperature
0x05 0x050 4 - --- Time in Over-Temperature
0x05 0x058 1 70 --- Specified Maximum Operating Temperature
0x05 0x060 4 - --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 13903 --- Number of Hardware Resets
0x06 0x010 4 0 --- Number of ASR Events
0x06 0x018 4 3 --- Number of Interface CRC Errors
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
0x07 0x008 1 4 N-- Percentage Used Endurance Indicator
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x000a 4 0 Device-to-host register FISes sent due to a COMRESET
Crucial 自己的 SMART 报告：
我不太确定如何解释 gsmartctl 输出，但我不相信 SMART PASSED 结果是正确的。是时候清理并更换该驱动器了吗？
r2d*_*2d3 12
忘记查看交通灯类型的自检。您已获得大量信息（智能数字），您只需要对其进行评估即可。无论如何，制造商没有兴趣展示负面的检查结果。也许应该用两盏巨大的灯取代驾驶舱内的所有空客仪表，分别为红色和绿色，分别代表“通过”和“失败”？:)
与其他人所说的相反，忽略标准化值，因为标准化过程没有定义的规范。因此，相同的 RAW 输入在一个制造商和另一个制造商之间以标准化术语给出不同的输出。
在 HDD 上，重新分配的扇区计数的原始值大于 0 的任何值都是失败指示器 - 其他一些用户在超级用户上写下此内容，指的是 Google 或 Backblaze。与 HDD 不同，扇区或更确切地说闪存块重新分配是 SSD 使用过程的一部分。在您的情况下，36864 在 HDD 世界中是一个巨大的数字，对于 SSD 来说可能并不重要。我宁愿查看磨损指示器 ID 202。不要期望线性增长，因为该指示器可能会考虑备用闪存块的数量和其他演算。
SSD 的破坏性分区
由于我缺乏使用 SSD（相对于 HDD）的 SMART 数字的经验，我无法回答您的问题，但如果您想保留此 SSD，请查看 ID 181。此 SMART 参数表明您以错误的方式对 SSD 进行分区会导致写入放大，从而增加 SSD 的磨损。
https://en.wikipedia.org/wiki/Write_amplification
当您对 SSD 进行分区时，您很可能使用的是旧版操作系统，例如 32 位 Windows XP。XP 32 位尝试将分区开始放置在柱面边界上，而不是兆字节的倍数 (2^20)。这种操作方式与将分区起始位置放置在内部物理扇区大小的非小数倍上的需要相冲突。在您的情况下，分区的起始 LBA 编号应可被 4096 整除。（必要条件：LBA 编号 MOD 4096=0）。现在情况并非如此。
将 SSD 的内容复制到安全位置，删除分区表并使用现代操作系统对 SSD 重新分区。现代操作系统很可能会将分区起始位置设置为 1 MB 的倍数，这也符合上述条件。将您的内容复制回 SSD。通过这样做，您可以减少写入放大，从而减轻 SSD 的未来磨损。
您可以使用 Testdisk 写入包含当前分区方案的日志文件。lsblk我想或fdisk也有合适的参数。
我不确定 gsmartcontrol 是否真正理解并正确报告所有 SMART 属性，或者磁盘固件是否正确报告其 SMART 属性。
SMART 属性显示一些错误和磁盘较弱，但不是灾难性状态，但自检失败并且您报告一些文件损坏。
最令人费解的是“重新分配的扇区计数”，其原始计数为 36864，这是灾难性的，但其标准化值相当不错，为 99，仅略低于最佳值 100。
除非你喜欢危险的生活，否则我会代替你更换这个磁盘。
我看到你添加了Crucial自己的SMART报告，比gsmartcontrol的清晰多了。
这些是危险信号：
364544 Retired NAND Blocks
20 NAND Page Program Failures
64 NAND Block Erase Failures
582 ECC Correction Failures
353 Corrected ECC
这里最糟糕的数据是退役 NAND 块的数量，由 Cruclial 的 SSD 和 SMART Data定义：
属性 5：退役的 NAND 块
通过持续评估 NAND 块质量的过程中报废的块数量在 SMART 属性 5 中进行跟踪。除了上述磨损和数据保留问题之外，SSD 固件还会出于多种原因报废 NAND 块。退役的原因之一是在垃圾收集期间删除数据或移动数据时未能擦除块。此类故障对用户数据造成的风险较低，因为相关数据正在被删除或已成功复制到 SSD 上的新位置。
这意味着磁盘上的 364544 个块已经随着年龄的增长而变得无法使用！这是巨大的。
最终预测：磁盘出现故障并接近其使用寿命。您应该尽快更换它。
- 可能不适用于此磁盘，但我有一些希捷硬盘，它们可以使用原始 SMART 值进行操作。在这些驱动器上，“寻道错误计数”将“寻道总数”打包到较低位中，这使得它看起来非常频繁地失败。 (5认同)
| 归档时间： |
|
| 查看次数： |
4851 次 |
| 最近记录： |